Sivun sisältöön
seventy years logo
Thomann juhlii juhlavuottaan! Kiitos uskollisuudesta! Tutustu juhlavuoden tarjouksiimme nyt. Tarjouksiin

Hicon HI-J63SA05 Angled Jack

148

Angled jack

  • Extremely flat 6.3 mm angle jack
  • Stereo
  • For cable diameters from 4.0 - 6.4 mm
  • Especially suitable for floor effects
Myynnissä vuodesta Joulukuu 2015
Tuotenumero 377803
Myyntierä 1 kappaletta
Installation No
Mono/Stereo Stereo
Angled Yes
Type TRS (stereo/sym.)
Plug Jack 6,3 mm TRS male angled
2,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Tiistai, 10.09. - Keskiviikko, 11.09.
1

148 Asiakkaiden arviot

4.4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

87 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
t
ground contact is missing
t3hh 23.03.2022
contact for soldering the ground wire is missing. The best solution would be soldering the ground into the nickel plated case but this is somewhat complicated process. You need to use acid based active flux (rosin based flux wont work) and more powerful iron. Don't forget to clean the flux after the soldering, it contains acid and will corrode. Some people leave the ground wire unsoldered and use the pressure to make a ground connection but this can not be suggested for critical audio work.
Työnjälki
2
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
d
Can’t recommend
daTroll 09.05.2021
Only get this if you have no other choice, e.g. if the space is limited. There is no solder lug for the sleeve/shield, so you either try to solder it anyway or just let the shield get crimped when you screw the plug pieces together. Another big problem is quality. One of the plugs I bought wasn’t manufactured correctly in that the tip was loose and could be rotated together with its solder lug. O_o
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
BE
Quality good but design not so
Bo E. 04.05.2016
For all my patch cables I use the mono variant and couldn't be happier! The stereo ones however... You have two solderpoints, one L and one R but the earth has no real soldering contact and has to be pressed against the enclosure of the jack to make contact... which fails eventually... I swear by the mono ones for all my patch cables but the stereo is not recommended !
Työnjälki
2
1
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
R
Needed this one
Recorick 08.06.2024
I got these for tap tempo on my delay, I needed 90 degrees for tight fitting on my pedalboard.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta