Till sidans innehåll
compare-box

Millenium DS200 Black

154

Table Microphone Boom Arm

  • Aluminium construction
  • Locking centre joint
  • 5/8" threaded connector
  • Table clamp for up to max. 56 mm table thickness
  • Pre-wired with XLR cable
  • Length of upper arm: 43 cm
  • Length of lower arm: 40 cm
  • Maximum load capacity: 1.5 kg
  • Colour: Black
Tillgänglig sedan September 2018
Artikelnummer 437359
försäljningsenhet 1 Styck
Type Microphone Boom
Colour Black
Weight 1,8 kg
Visa mer
B-Stock från 598 kr tillgänglig
759 kr
Alla priser inklusive moms
i lager
1
Standardleverans
69 kr

Väntas mellan Ons., 9.04. och Tors., 10.04..

154 Kundbetyg

4.2 / 5
Betygsätt nu

stabilitet

hantverkskvalitet

100 Recensioner

R
Hur bra som helst
Roze 01.03.2021
Lite stiff i armen med annars är den hur bra som helst, det går att ändra hur lätt som helst och jag älskar att xlr kablen är inbyggd in armen, mycket mindre kablar att hålla reda på
hantverkskvalitet
stabilitet
0
0
Anmäl recension

Anmäl recension

F
Stabil och väl fungerande.
Fredrik6714 14.11.2020
Se ovan. =)
Jag har inte använt mikkabeln som finns inbyggd i stativet men själva stativet är bra.
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
P
not bad but room for improvement
PKristoffersson 13.02.2020
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
2
1
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
S
had this for about 1 year
SixStackJack 06.01.2022
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it wont move eaven if there was an earthquake :;D
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it wont move eaven if there was an earthquake :;D
hantverkskvalitet
stabilitet
0
0
Anmäl recension

Anmäl recension

Visste du?