Adam Hall 5635 Humfrees M6

311

Iniciar 360°

Mostrar tradução

Rack Insulation Against Ground Loops

When rack mounting, additional conducting ground connections are created between 19" devices via the metal rails - the most frequent cause of hum noise.

Humfrees interrupts these ground loops. Devices are attached to the rack rails while electrically separated from each other. Additional plus: The front panels of the devices are protected against assembly damage.

4 M6 screws
4 Insulators
4 Spacers

30 dias dinheiro de volta

Thomann garantie de 3 anos

Disponível desde Novembro 1999

número de artigo 128225

unidade de venda 1 peça(s)

Type Set

Thread Size M6

Length 16

Amount 4

Note Rack Isolation

Mostrar mais

€ 3,50

IVA incluído, € 9,90 de portes de envio adicionais

Desconto de quantidade

Preço unitário	Poupará	Montante
€ 3,50		1
€ 3,29	6,0%	4

Posição de vendas

em Parafusos

Eis o que compraram os clientes que visualizaram este artigo

36%

comprado

Este artigo exatamente

€ 3,50

15%

comprado

Adam Hall 5621 Plain Nylon

€ 1,90

14%

comprado

Adam Hall 5410BLK Rack Screw Pack

€ 3,50

comprado

Adam Hall 5417BLK Rack Screw Pack

€ 2,90

comprado

Adam Hall 5620 Plastic Washer Pack

€ 2,70

311 Avaliações de clientes

5 148 Clientes 4 92 Clientes 3 39 Clientes 2 15 Clientes 1 17 Clientes

4.1 / 5

acabamento

Diretrizes de apreciações

137 Críticas

Mostrar tradução

Mostrar original

Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.

bad product

ColmO 18.03.2014

its only true purpose is to prevent against rack rash, it does not isolate equipment from each other, rather it isolates the rack equipment from the rack rails, so if 1 unit is causing hum this will transfer along each unit as their faceplates arent isolated

the screws dont fit my adam hall rack or gator case, it comes with a soft adapter for smaller screws

you have to cut the pieces out of their molds which isnt too difficult, but takes some accuracy to get them looking smooth with no bits sticking out.

the rubber/plastic warps/goes out of shape and shift position before you have the screws tightened, its difficult to gauge when its tight enough, when it feels tight your left with a misshapen piece

I dont normally right reviews straight after using a product but was so let down by these that I felt the need to write a review. some old bicycle inner tube would work better, or 2 plastic washers per screw would achieve the same

Reportar a crítica

Acredita que esta classificação seja por alguma razão imprecisa ou incaceitável? Indique-nos por favor a justificação na caixa de texto em baixo e se possível o seu endereço de email para eventuais questões.

Mostrar tradução

Mostrar original

Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.

Your rack deserves the best!

SpyX 14.06.2018

Your rack deserves the best.
If you are a pro you don't need my advice, you know what you'll do. But for the rest of us who build a rack I'll tell you that, this set is a must for your rack.
You have spend a lot of money to buy audio hardware devices, you want the best for your sound so the last thing you want is hum from ground loops created between 19" devices via the metal rails.
Here comes the "Adam Hall 5635 Humfrees M6".
Consists of (4) M6 screws, (4) Insulators and (4) Spacers this is a set for one device. In a very good quality it'll give insulation to your rack against ground loops and protection to the front panels of your devices against assembly damage. Also looks nice aesthetically.
Coming in a good price, don't even thinking to don't make this buying.

Reportar a crítica

Mostrar tradução

Mostrar original

Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.

Quite good

svenoxtoby 11.05.2017

I have used these in many racks with both M5 and M6 screws. These ARE compatible with both M5 and M6 screws because adaptors are provided for M5 screws.

As noted by another reviewer the can get mis-shapen if you are not careful, but this has only been a cosmetic problem for me.

As for isolation, they have worked every time for me (tested). I have not had trouble keeping the faceplates isolated. Important: when testing for isolation/continuity, remember to unplug all of the power cables from power distribution unit to rack devices. Otherwise the meter will indicate continuity, since the devices are joined through the PE/ECC conductor of each piece of gear (and this is how it must be for safety - NEVER cut a ground/PE/ECC conductor.

Reportar a crítica

Mostrar tradução

Mostrar original

Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.

Product is fine but a few quality issues

MrMesh 21.03.2019

I bought about a dozen of these to try and help deal with hum issues from my rack gear. For the most part they are effective, but at times the installation is troublesome and the the plastic that wraps around the rack ears is prone to breaking. In addition, the heat shrink around the screws can either come loose or isn't secured properly to the screw, so a heat gun is required in the event anyone has similar issues.

Reportar a crítica

Ler todas as reviews

Adam Hall 5635 Humfrees M6

Rack Insulation Against Ground Loops

Eis o que compraram os clientes que visualizaram este artigo

311 Avaliações de clientes

Terá de iniciar sessão para classificar produtos.

137 Críticas

Navegador inteligente

Servido com amor!

Adam Hall 5635 Humfrees M6

Rack Insulation Against Ground Loops

Eis o que compraram os clientes que visualizaram este artigo

Acessórios e artigos correspondentes

311 Avaliações de clientes

Terá de iniciar sessão para classificar produtos.

137 Críticas

Comparar opções

Navegador inteligente